⚡ Black Friday Offer: Click here and shop now!

TextRanch

The best way to perfect your writing.

Discover why 1,062,726 users count on TextRanch to get their English corrected!

1. Input your text below.
2. Get it corrected in a few minutes by our editors.
3. Improve your English!

One of our experts will correct your English.

Our experts

a load is applied vs loads are applied

Both phrases are correct, but they are used in different contexts. 'A load is applied' is used when referring to a single load being applied, while 'Loads are applied' is used when referring to multiple loads being applied.

Last updated: March 30, 2024 • 797 views

a load is applied

This phrase is correct and commonly used when referring to a single load being applied.

This phrase is used when talking about the action of applying a single load to something, such as in engineering or physics.

Examples:

  • A load is applied to the structure to test its strength.
  • In this experiment, a load is applied to the material to measure its deformation.
  • When in the secondary latched position, the primary latch system shall not separate when a load of 4500 N is applied in the same direction as in paragraph 6.1.1.1, when tested in accordance with paragraph 7.1.1.1.
  • The vertical plane in which the load is applied shall be located at a distance of one third of the external width of the upper part of the structure from the median plane.
  • There is no need to measure the force and deflection at the point where the load is applied to the structure; however, force and deflection shall be measured simultaneously and co-linearly.
  • If the vehicle is fitted with a badge, mascot or other structure which would bend back or retract under a low applied load, then such a load shall be applied before and/or while these measurements are taken.
  • The porcelain peg is brought onto the sample under test and the load applied.
  • The 5 daN load applied on the test bench shall be guided vertically in such a way as to prevent the load swaying and the belt twisting.
  • If the structural member to which the load is to be applied is curved, the specifications laid down in point 2.1.2.5 of Annex II must be complied with.
  • load applied in crushing tests: ± 2 %;
  • This covers principally expenditure in respect of works in connection with the mechanical resistance of roads to the loads applied to them.
  • The two loads need not be applied simultaneously.
  • The load is to be applied through the centreline of the hinge pin in a direction orthogonal to the longitudinal and transverse loads. (see Figure 5-2).
  • Starting with no load, the load applied must be increased until the maximum noise level is found.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Both tractive and compressive test loads are applied on each separate towing device fitted to the vehicle.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Care should be taken to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • It shall be confirmed that, when taking into account the loads applied during operation of the working gear and whilst under way, the residual freeboard and the residual safety clearance are sufficient.
  • the dynamic load applied to the rail by the wheel,
  • The instruments used to record loads applied and movements must have the following degree of accuracy:

Alternatives:

  • A single load is applied
  • One load is applied
  • A load is being applied
  • The load is applied
  • Applying a load

loads are applied

This phrase is correct and commonly used when referring to multiple loads being applied.

This phrase is used when talking about the action of applying multiple loads to something, such as in engineering or construction.

Examples:

  • In the testing process, loads are applied to different parts of the structure.
  • During the construction, various loads are applied to ensure stability.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Both tractive and compressive test loads are applied on each separate towing device fitted to the vehicle.
  • Care shall be exercised to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Care shall be exercised in holding the T-bar and rocking the 3-D H machine to ensure that no inadvertent exterior loads are applied in a vertical or fore and aft direction.
  • Care should be taken to ensure that no exterior downward or lateral loads are applied to the 3-D H machine.
  • Steps and handrails shall be designed to withstand the loads that are applied by the shunter.
  • The handrails shall withstand the loads, which are applied by the shunters while accessing the space between the buffers.
  • During this lifting, the feet are to be free to rotate; and no forward or lateral loads are to be applied.
  • The porcelain peg is brought onto the sample under test and the load applied.
  • The 5 daN load applied on the test bench shall be guided vertically in such a way as to prevent the load swaying and the belt twisting.
  • load applied in crushing tests: ± 2 %;
  • This covers principally expenditure in respect of works in connection with the mechanical resistance of roads to the loads applied to them.
  • The two loads need not be applied simultaneously.
  • Starting with no load, the load applied must be increased until the maximum noise level is found.
  • It shall be confirmed that, when taking into account the loads applied during operation of the working gear and whilst under way, the residual freeboard and the residual safety clearance are sufficient.
  • the dynamic load applied to the rail by the wheel,
  • The instruments used to record loads applied and movements must have the following degree of accuracy:
  • Two load cells of sufficient capacity to measure the applied loads.
  • The projection is measured under the applied load.

Alternatives:

  • Multiple loads are applied
  • Several loads are applied
  • Loads are being applied
  • The loads are applied
  • Applying loads

Related Comparisons

What Our Customers Are Saying

Our customers love us! We have an average rating of 4.79 stars based on 283,125 votes.
Also check out our 2,100+ reviews on TrustPilot (4.9TextRanch on TrustPilot).

Why choose TextRanch?

Lowest prices
Up to 50% lower than other online editing sites.

Fastest Times
Our team of editors is working for you 24/7.

Qualified Editors
Native English experts for UK or US English.

Top Customer Service
We are here to help. Satisfaction guaranteed!

×

⚡️ Black Friday 2024 ⚡️

Stock up on credits for the entire year!

Grab this offer now!